Sitecom WLM-4550 Manuale Utente

WLM-4550 Wireless ADSL2+ Gigabit Modem Router User Manual Version: 1.0

5 System Requirements To begin using the WLM-4550, make sure you meet the following as minimum requirements: • PC/Notebook. • 1 Free Ethernet por

8 PC Network Adapter setup Windows XP • Go to [Start Menu],  [Control panel],  [Network Connections]. • Right-mouse-click on the [Local Area

Windows Vista/Windows 7 • Go to [Start Menu],  [Control panel],  [View network status and tasks], -> [Manage network connections]. • Ri

• Select [Internet Protocol Version 4 (TCP/IPv4)], and Click [Properties]. • Open the [General] tab. The WLM-4550 supports DHCP. Please se

9 Bring up the WLM-4550 Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Press the Power-Button to turn t

Status The pages in the status section provide you general information about the operational status of your device. Status The System stat

Statistics You can view statistics on the processing of IP packets on the networking interfaces. You will not typically need to

DHCP List This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC a

Diagnostics The Diagnostics page allows you to test the current configuration. Click ‘Start’ to let the modem router perform several tasks to veri

11 Configuration Wizard Click Wizard to configure the modem. The Setup wizard will now be displayed; check that the adsl line is connected and cl

Table of Contents INTRODUCTION... 4 1 KEY FEATURES...

12 Basic Settings LAN Settings This page is used to configure the LAN interface of your ADSL Router. You can set IP address, subnet mask, and I

DHCP Settings You can configure your network and the router to use the Dynamic Host Configuration Protocol (DHCP). This page allows you to select

WAN Settings This page allows you to manually configure the ADSL/WAN settings. The settings on this page require some knowledge concerning the WAN

ATM VC • Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. • VPI: The valid range for

• Network Address Translation: Select None, Many to One or Many to Many from the drop-sown list box. Refer to the NAT chapter for more details. • R

Wireless Settings This section provides the wireless network settings for your router. You can enable and configure the wireless AP function here.

for 802.11b clients, maximum 54Mbps for 802.11g clients, and maximum 150Mbps for 802.11n clients). Mode It allows you to set the router to act in “A

Security Settings This router provides complete wireless LAN security functions, include WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-sha

IEEE 802.1x. WEP-64Bits WEP is less level of security than WPA. WEP supports 64-bit and 128-bit key lengths to encrypt the wireless data. The longer

Wireless ACL This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Pa

ACL 41 IP FILTER 42 DMZ 45 VIRTUAL SERVER 46 15 TOOLBOX SETTINGS ... 47 PASSWO

13 Advanced Settings The advanced settings pages allow users to modify the more complex features of this device. Advances wireless This pag

DTIM Broadcast SSID If this option is enabled, the router will automatically transmit the network name (SSID) into open air at regular interval. T

QoS QoS allows you to classify Internet application traffic by source/destination IP address and port number. You can assign priority for each typ

Enable/Disable QoS You can check “Enable QoS” to enable QoS functionality for the WAN port. Add a rule Enter all the data required for th

UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Windows 7. The router will be displayed in the

Routing The page enables you to define specific route for your Internet and network data. Most users do not need to define routes. On a typical s

SNMP Simple Network Management Protocol (SNMP) is a troubleshooting and management protocol that uses the UDP protocol on port 161 to communicate

DDNS Dynamic DNS (DDNS) allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain

NAT This page allows viewing or changing of the current status of the NAT for each VC. Here it’s possible to set Virtual server or DMZ settin

TR-69 As a bidirectional SOAP/HTTP-based protocol, it provides the communication between customer-premises equipment (CPE) and Auto Configuration S

Introduction Congratulations on your purchase of the WLM-4550 Wireless ADSL2+ Modem. This modem is fully compliant with 802.11b, 802.11g and 802.

14 Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of ha

ACL This page is used to IP addresses for Access Control. If ACL is enabled only the IP Addresses that are in the ACL Table can access the CPE.

IP Filter Filter Type Choose the type of filter you wish to use, there are 3 possible types of filter . - IP/Mac Filter - Application filter

set from range 0 ~ 65535. It is recommended that this option be configured by an advanced user. • Destination IP Address: This is the destination su

Application filter Here you can choose which applications should be blocked or allowed access. Choose which application should be allowed or den

DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP Address as the DMZ Host, all incoming packets

Virtual server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Inter

15 TOOLBOX Settings Password This page allows you to set the password to access the web server of the router. If the password you typed in ‘

Please use new password to enter web management interface again, and you should be able to login with new password.

Time Settings The Time Zone allows your router to set its time; especially for recording System Log. Parameter Description Current Time The cu

1 Key Features Features Advantages IEEE 802.11g compliant Fully Interoperable with IEEE 802.11b / IEEE802.11g compliant devices Based on 802.11n

Firmware Upgrade Enable Automatic firmware update When enabled the router will check for updates on the firmware if an updated firmware has bee

Reboot Whenever you use the Web configuration to change system settings, the changes are initially placed in temporary storage. To save your chan

2 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard th

3 Cautions This router’s design and manufacturer has your safety in mind. In order to safely and effectively use this router, please read the foll

4 Product Layout Port Description ADSL Connect your telephone/ADSL cable this port LAN Connect the cable from your PC or net

Back label The back label describes the corresponding LED indications and port functionality. LED Description Power Lights up when powered ON. B