WLM-5600 User Manual
Setup your Router You can place the router on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your rout
Setup your Computer Windows, Manual Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to
Windows, OPS Connection Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select th
Mac OSX Click on the icon for wireless connectivity. This is usually located in the System Tray, next to the clock. Select the Sitecom networ
Login to your Router LOGIN procedure • OPEN your browser (e.g. Internet Explorer). • Type http://sitecom.modem or http://192.168.0.
Configure your Internet connection From the menu, select “Internet Settings”. Depending on the chosen setting, you may need to enter your user nam
IPv6 Configuration The IPv6 (Internet Protocol version 6) section is where you configure your IPv6 Connection type. IPv6 Connection Type There are
6RD Mode In the 6RD mode, no additional configuration is necessary. Link-local Mode The Link-local address is used by nodes and routers when comm
Status The pages in the status section provide you general information about the operational status of your device. Status The System status secti
Statistics You can view statistics on the processing of IP packets on the networking interfaces. You will not typically need to view this data, but
Table of Contents Introduction ... 3 Key Fea
Diagnostics The Diagnostics page allows you to test the current configuration. Click ‘Start’ to let the modem router perform several tasks to veri
Configuration Wizard Click Wizard to configure the modem. The Setup wizard will now be displayed; check that the adsl line is connected and click “
Depending on the chosen provider, you may need to enter your user name and password or hostname in the following window. After you have entered the
Basic Settings LAN Settings This page is used to configure the LAN interface of your ADSL Router. You can set IP address, subnet mask, and IGMP Sno
You can configure your network and the router to use the Dynamic Host Configuration Protocol (DHCP). This page allows you to select the DHCP mode t
WAN Settings This page allows you to manually configure the ADSL/WAN settings. The settings on this page require some knowledge concerning the WAN
may already be configured. ATM QoS: Select CBR to specify fixed (always-on) bandwidth for voice or data traffic. Select UBR for applications that ar
2.4GHz/5GHz WiFi This section provides the wireless network settings for your router. You can enable and configure the wireless AP function here. S
Security Settings This router provides complete wireless LAN security functions, include WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-share
WPA Authentication Mode: There are two types of authentication mode for WPA. Enterprise (RADIUS): It uses an external RADIUS server to perform user
Introduction Congratulations on your purchase of the WLM-5600 Wireless ADSL2+ Modem. This modem is fully compliant with 802.11a, 802.11b, 802.11g a
Allow: Only allow the wireless clients with the MAC Address you have specified can access to the router. Deny: The wireless clients with the MAC Add
When you finish, click ‘Save’ to save the settings made and restart the router so the settings will take effect after it reboots. Wireless WPS Wi-F
Advanced Settings QoS QoS allows you to classify Internet application traffic by source/destination IP address and port number. You can assign prio
UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Windows 7. The router will be displayed in the
You may need to define routes if your home setup includes two or more networks or subnets, if you connect to two or more ISP services, or if you con
DDNS Dynamic DNS (DDNS) allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain
TR-69 As a bidirectional SOAP/HTTP-based protocol, it provides the communication between customer-premises equipment (CPE) and Auto Configuration S
Firewall The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks,
IP Filter Click “Add a rule” to add a filtering rule. Enable: Select to enable IP filter rule. Source IP: The source IP address or range of packe
When you finish, click ‘Submit’ to save the settings made. IP Filter Listing #: Item number. Enable: Whether the connection is currently active. Sr
Key Features Features Advantages Incredible Data Rate up to 300Mbps* Heavy data payloads such as MPEG video streaming IEEE 802.11n Compliant and ba
URL Filter Here it’s possible to block certain websites. Enter the website you wish to block and make sure the rule is active. Click ‘Save’ to app
Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet application
Note : The ports from the start port till the End port will be opened Click ‘Apply’ for the changes to take effect. TOOLBOX Sitecom Cloud Security
With the protection of unsafe websites activated the Sitecom Cloud Security will always check if a website is safe. If it is not safe it will inform
Or click ‘License’ to renew your subscription. Disabling Sitecom Cloud Security If you wish to disable to Sitecom cloud security at any time, open
Go to Toolbox and select “Sitecom Cloud Security”. Click the “Disable” radio button and click ‘Apply’ for the settings to take effect. Password You
Current Time: The current time of the specified time zone. You can set the current time by yourself or configure by NTP server. NTP server: The IP
Enable Automatic firmware update: When enabled the router will check for updates on the firmware if an updated firmware has been released the route
Addendum A: USB Port Control Center The netUSB functionality of your router requires additional software to work with your computer. The following
Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard the packing materials, i
Enter your username and organization if applicable and click Next to continue. Choose a folder where the software should be installed or keep it t
The software is now ready to be installed, Click Install to continue. Once the installation is finished the software will inform you. If “Launch S
MacOS Insert the CD-ROM that was included with your router and select “Install” from the cd-menu. Click Install to continue installation. Enter yo
Connect & Disconnect “NetUSB” allows you to use USB printers when they’re actually connected to the Sitecom USB server. The “connect” operation
NetUSB installation The steps to do installation for USB devices, like MFPs: Make sure the router is turned on. Connect the USB device to the
PC will automatically detect that the USB device is plugged-in. On the right side of the Windows Task Bar, you can see the information of the ne
NetUSB Printing using Auto-Connect Printer After the driver is installed, you can see a newly created printer in the Control Panel. Follow the steps
When you do a print job again. The control center will automatically do a connecting operation on printing again. This is so-called “Auto Connect
NetUSB Scanning using Network Scanning In the Control Center, click the MFP server that has the desired MFP attached. Click the desired MFP.
Follow the usual steps to do scanning.
Cautions This router’s design and manufacturer has your safety in mind. In order to safely and effectively use this router, please read the followi
Addendum B: Declaration of Conformity
Product Layout Port Description Power connector Connect the 12V DC adapter to this port USB Port Connect a USB device to this port LAN (Yellow) Co
LED Definition As shown from the top to the bottom. Port Description Power (Red) Shows the device is turned on. DSL (Green) Shows the DSL signal is
Network + System Requirements To begin using the router, make sure you meet the following as minimum requirements: PC/Notebook. Operating Sys
Commenti su questo manuale